banner

Vertical Bar Racks Industrial Storage Systems

Herochu Vertical Bar Racks Industrial Storage Systems
Stand it up, lock it down, reclaim the floor—starting at $3,099, CE/UE/ISO 9001 certified, and cut to the exact height your roof allows.


Horizontal bundles turn forklift aisles into slalom courses. One sharp brake and a ton of bar stock rolls, taking guard rails, sprinkler heads, and ankles with it. Herochu Vertical Bar Racks Industrial Storage Systems end the demolition derby by parking every round, square, or flat bar on its own rubber-cradled foot—upright, visible, and reachable in the time it takes to read this sentence.


Gravity Does the Work, You Take the Credit

Stand a 6 m stainless shaft on its end and only 100 mm of floor disappears. Lay the same shaft down and you lose 12 m² plus the access lane. Herochu towers exploit height that most warehouses already pay rent on but never use. A single 3 m wide bay stores 22 tons of bar, tube, or extrusion while the forklift drives past without slowing. One operator, one remote, zero spotters—productivity climbs, labor hours fall, and the safety officer finally posts a green metric on the board.


Modular Spine, Snap-In Cradles

Uprights start at 2 m and climb in 500 mm increments until they kiss the rafters at 12 m. Each spine is a 200×100 mm closed box, 6 mm wall, punched on 100 mm centres so cradles relocate without drilling. Slide in a cradle, drop the safety pin, and the arm is rated for 2 t in thirty seconds. Need to switch from 50 mm round bar to 300 mm wide flat? Swap the cradle, don’t buy a new rack. The steel you bolt together today accepts tomorrow’s product mix—no welder, no cutting disc, no capital request.

Industry Pipe Storage and Racking Solutions
Industry Pipe Storage and Racking Solutions

Rubber Meets Steel—Damage Dies Here

Cradles are laser-cut from 8 mm plate, folded to a 110° vee, then over-moulded with 5 mm oil-resistant nitrile rubber. Hard enough to support 42 CrMo drill rod, soft enough to keep polished 316 round bar mirror-bright. Divider fingers every 150 mm keep bars separate so carbon dust doesn’t migrate to stainless, and the vee angle self-centres stock within 2 mm—handy when the saw wants an exact feed line.


Base Plates That Grip Concrete, Not Dreams

A 3 t cradle 4 m in the air generates serious overturning moment. Herochu bases are 800 mm deep, 12 mm plate, gusseted both sides and pre-slotted for M20 chemical anchors. Installers torque anchors to 180 Nm, lock the nut, and the rack is certified for seismic Zone 4 without rear bracing—leaving the front open for forklift approach. Should you relocate, grind the anchors, patch the holes, and bolt the same rack down in the next bay. Reuse beats recycle every time.


Vertical Doesn’t Mean Wobbly

Every bay ships with bolt-on sway braces and a top tie-bar. Tighten four bolts and the structure becomes a torsion box; bump one cradle and nothing shimmies. A Pennsylvania tool-and-die shop hit a tower with an 8 t load at 5 km/h—cradle absorbed the impact, upright stayed plumb, bars never touched the floor. Insurance inspector wrote “best practice” in the report instead of the usual fine.

Double sided cantilever rack
Double sided cantilever rack

Weight Stack That Scales With Your Appetite

Start with three cradles and 6 t of capacity. Land a new contract for 2205 duplex bar? Add four more cradles at 2 t each and the same tower now holds 20 t—no additional footings, no extra concrete. Load labels are laser-etched into each arm, so even after ten years of repaint the rating remains legible. Forget the laminated tag that peels; Herochu speaks in steel.


Colour That Cuts Chaos

Orange cradles for carbon steel, blue for stainless, grey for aluminium—visual factory rules baked into the powder coat. End-stops accept barcode holders or RFID pucks, so the scanner knows cradle 3-B contains 316 L, 50 mm, 3 m lengths, 18 pieces left. One beep updates ERP, triggers reorder, and emails the purchaser before the bar hits the saw infeed.


Outdoor Brain, Indoor Brawn

UV-stable polyester survives Arizona summers; optional roof panel kit clips to the top beam and turns any tower into a mini canopy for less than the cost of a tarp that flaps. Ventilated cradles keep condensation from pooling, so 17-4 PH round bar doesn’t surprise you with surface rust Monday morning. Galvanised finish pushes corrosion resistance to 2,400 h salt-spray if you store near the ocean; we galvanise after fabrication so threads still fit and pins still slide.

Cantilever Pipe Rack System
Cantilever Pipe Rack System

Assembly Without the Three-Ring Circus

Uprights arrive pre-punched, cradles labelled left-to-right, and bolts bagged by step number. Two fitters, two 19 mm wrenches, and 60 minutes erect a 4 m double-sided bay—no boom lift, no certified welder, no hot-work permit. A QR code on the mast links to a 2-minute video shot in one take so second shift can add a level while first shift clocks out. Lost a pin? Standard M20 grade 8.8 hardware sits on every hardware-store shelf.


Lead Times Measured in Days, Not Quarters

Cradles are plasma-cut within 24 h of order; uprights are welded, shot-blasted, and powder-coated by day three. A six-bay row leaves the plant in 8 business days; custom height or hot-dip finish adds four. Miss the promised dock date and we credit the expedite fee—no asterisks, no haggling.


Sustainability Welded In, Not Bolted On

Steel averages 72 % recycled content, powder line runs on rooftop solar, and returnable steel frames replace timber crating. When product mix changes, unbolt and reuse 98 % of components; only the anchors stay in the concrete. Your ESG slide gets a bullet point, landfill gets nothing, and finance doesn’t have to depreciate scrap.

Custom Single Sided Roll Out Racks Solutions
Custom Single Sided Roll Out Racks Solutions

Talk to Someone Who Has Loaded Bar at 5 a.m. in January

Dial 1-800-HEROCHU and you reach a former yard foreman, not a script. Email a napkin sketch; we return a stamped drawing and anchor layout overnight. Need a load test? We’ll video 2.5× proof and send the MTRs with the invoice. Your inspector signs off before the truck backs in.


Ready to Give Every Bar a Seat Belt?

Measure the longest length, the heaviest bundle, and the roof you can’t hit. Punch those three numbers into the Build-My-Rack widget and watch a live quote populate—freight included, taxes optional, payback curve attached. Or call the number, ask for vertical, and speak to someone who knows why 316 round bar always rolls the wrong way.

Herochu Vertical Bar Racks Industrial Storage Systems
Stand it up, lock it down, reclaim the floor—one cradle at a time.

PRODUCTS

Frequently-Asked Questions

Q1: How do I start the purchasing process?
Reach our back-end engineers directly; they will draft a tailored technical proposal and quote according to your parameters. Alternatively, leave your WhatsApp, WeChat, or email—our sales department will follow up promptly.
Q2: How can I request the correct shelving?
Describe the items you plan to store, including dimensions, required shelf quantities, and any special details. We will create a bespoke plan. You may also leave your contact details for our specialists to respond.
Q3: Do I need a loading robot arm or a complete loading & unloading system?
The choice depends on your laser-cutting table size and the loading style—board rack, exchange platform, or material warehouse. Tell us your needs or provide contact information, and we will guide you.
Q4: Do you offer on-site installation and commissioning?
Yes, our technicians travel worldwide to install and commission the robot arm until it runs smoothly. We have completed projects in South Africa, the United States, Russia, South Korea, Qatar, Egypt, Lebanon, Mexico, and more.
Q5: How is product quality guaranteed?
Over 40 engineers support every project; mechanical specialists handle debugging. An independent QC department enforces ISO9001 standards, and CE certification secures global shipments. Each unit undergoes load tests before leaving the plant to confirm structural safety and stability.
Q6: Where is your factory?
Our 10,000 m² modern facility sits in Building 2-1, Jiyang Industrial Park, Jinan, Shandong, China.
Q7: How can I verify your company strength?
We arrange live video factory tours and warmly welcome in-person visits.
Q8: What does your company do?
Jinan Constant Storage Machinery Manufacturing Co., Ltd. is a high-tech firm covering R&D, production, sales, installation, and service. We specialize in intelligent sheet-metal warehouses, drawer-type shelves, telescopic cantilever racks, servo swing-arm manipulators, gantry loaders, fully-automatic loading & unloading lines, and heavy-duty sheet-metal and tube storage systems. A seasoned technical crew and state-of-the-art workshop deliver premium, high-performance machinery and solutions to clients worldwide.

Products Category

Sheet Metal Storage Racks
Sheet Metal Storage Racks
Heavy Duty Cantilever Racking System
Heavy Duty Cantilever Racking System
Sheet Metal Material Handling Equipment
Sheet Metal Material Handling Equipment
Automated Sheet Metal Storage Systems
Automated Sheet Metal Storage Systems
Fiber Laser Automation Systems
Fiber Laser Automation Systems
Scroll to Top

Contact Us

✶ ✶ ✶ Get a quote and more information now!!!